Metalsub Din300 Converter For First Stage

Automatic translation View in original language

Hi. does this converter fit Apeks DST/DS4 pls ? If not, is there a diffferent one (other than the very expensive Apeks one) that does ? thx.

Hi. does this converter fit Apeks DST/DS4 pls ? If not, is there a diffferent one (other than the very expensive Apeks one) that does ? thx.

Answer of wilbert timmermans

Answer of Rocco

No, it is not compatible with Apeks.

No, non è compatibile con Apeks.

Answer of Stéphane

Hello, it is suitable for the 1st stage of Scubapro MK2 regulators. With the Scubapro MK2 and Apeks technical sheets, could you check compatibility? Good luck !

Bonjour, il est adapté pour les 1er étage des détendeurs Scubapro MK2. Avec les fiches techniques de Scubapro MK2 et Apeks, vous pourriez vérifier la compatilibité ? Bon courage !

Automatic translation View in original language

Good morning, I´m wondering if it is compatible with a Cressi Ac2 first stage and if the conical filter is present.

Buongiorno, chiedo se è compatibile con un primo stadio Cressi Ac2 inoltre se è presente il filtro conico.

Answer of Frank van Rhijn

Answer of Carlos Javier

If it is compatible. I don´t remember if the filter is included. I don´t think so.

Si es compatible. No recuerdo si el filtro está incluido. Creo que no.

Answer of DAVID

Both this model of international regulator converter or bracket to DIN 300 bars, as well as the DIN 200 bar one, are fully compatible with CRESSI AC2 first stages.

Tanto este modelo de convertidor de regulador internacional o de estribo a DIN 300 bares, como el de DIN 200 bares, son totalmente compatibles con primeras etapas CRESSI AC2

Automatic translation View in original language

Hi, I kindly ask if it is possible for compatibility with Mares Mr22 VR16 Dacor first stages. Possibly you can know the length of the thread and the pitch. Thanks Andrea

Salve chiedo gentilmente se possibile la compatibilità con primi stadi mares Mr22 vr16 Dacor. Possibilmente si può sapere la lunghezza della filettatura e il passo. Grazie Andrea

Answer of zaid ali

Answer of Giuseppe Eros

Mounted on Scubapro MK17 first stage without problems. It was not possible to mount it on Mares MR 16 because the thread pitch is different.

Montato su primo stadio scubapro MK17 senza problemi. Su mares MR 16 non è stato possibile montarlo perché il passo del filetto è diverso.

Answer of Cándido Agustín

Hello. Before purchasing this part you must keep in mind that to convert an INT into a DIN you need more parts.

Hola. Antes de comprar esta pieza debes tener en cuenta que para convertir un INT en DIN necesitas más piezas.

Answer of Luis Angel

Hello Andrea, I do not know the compatibility of this converter with Mares, it is trial and error, it has worked for me with some scubapro and oceanic stages, greetings

hola Andrea, desconozco la compatibilidad de este convertidor con Mares, es ensayo y error, a mi me ha funcionado con algunas etapas scubapro y oceanic, un saludo

Automatic translation View in original language

Hello, is it compatible MK20 Scubapro? I have Mares and Aqualung. Which converters to take. Sincerely

Bonjour, est il compatible MK20 Scubapro ? J'ai du Mares et de l'Aqualung. Quels convertisseurs prendre. Cordialement

Answer of Frederic et Cathy LABORDE

Answer of DAVID

This Metalsub converter to transform stirrup regulators to DIN300 is universal, so, in principle, it would be valid for all models. I have installed them in Cressi AC2 regulators, adapting perfectly. You just have to remove the screw that fixes the stirrup and replace it with the converter, which must have the same thread pitch

Este convertidor de Metalsub para transformar reguladores de estribo a DIN300 es universal, con lo que, en principio, valdría para todos los modelos. Yo los he instalado en reguladores Cressi AC2 adaptándose perfectamente. Tan sólo hay que retirar el tonillo que fija el estribo y sustituirlo por el convertidor, el cual debe tener el mismo paso de rosca

Answer of Frederic et Cathy

It is not compatible with the Scubapro MK20, MK25, MK11 and MK17 For these models you must take https://www.tradeinn.com/diveinn/fr/tecnomar-convertor-din-int/661198/p

Il n´est pas compatible avec le Scubapro MK20, MK25, MK11 et MK17 Pour ces modèles il faut prendre https://www.tradeinn.com/diveinn/fr/tecnomar-convertor-din-int/661198/p

Automatic translation View in original language

is it work with apeks 1. stage regulator ? convert from YOKE to DIN ?

is it work with apeks 1. stage regulator ? convert from YOKE to DIN ?

Answer of zaid ali

Answer of ZHU

Not available for APKES REGULATOR, but can be used for CRESSI, and the test is OK

不可用于APKES REGULATOR , 但是可以用于CRESSI ，且测试OK

Automatic translation View in original language

Hello and reliable and compatible for scubapro mk11 int. Thanks in advance for the reply. F. F

Buongiorno e affidabile ed compatibile per scubapro mk11 int. Ringrazio anticipatamente per la risposta. F. F

Answer of Rocco

Answer of Rocco

Hi, yes but the int bracket must be disassembled, it is not an adapter that replaces the bracket.

Salve, sì ma va smontata la staffa int, non è un adattatore va a sostituire la staffa.

Automatic translation View in original language

When they refer to the DIN 300 converter as universal, do they mean that it is valid for any first stage that wants to pass to DIN 300 of any brand?

Cuando se refieren al convertidor DIN 300 como universal quieren decir que vale para cualquier primera etapa que se quiera pasar a DIN 300 de cualquier marca?

Answer of Mario

Answer of Mario

You have to be careful because it is NOT valid for any first stage. I bought it and it is not valid for scubapro or for the old town ones. Nor for beutchart. So I have not been able to use it and it has gone to the drawer.

Hay que tener cuidado porque NO vale para cualquier primera etapa. Yo lo compre y no vale ni para scubapro ni para las de casco antiguo. Tampoco para beutchart. Así que no la he podido usar y ha ido al cajón.