Yamaha Display 2016 handlebar cycling computer mount

Answer of Andreas

Hello, I´m not familiar with the bike, but I looked at the Gitane E-Salsa Yamaha N7 2018 bike online, and the photo of the display shown there is identical to the one on my Haibike Allmtn model from 2016. So the accessories should fit. Installation was easy...best regards!

Hallo, ich kenne das Rad nicht, habe mir das Gitane E-Salsa Yamaha N7 2018 Bike aber im Internet angesehen und das dort gezeigte Foto vom Display ist ident mit jenem von meinem Haibike Allmtn Mod. 2016. Das Zubehör müsste also passen. Die Montage war einfach...schöne Grüße!

Answer of Hubert

I have a 2017 Winora Y 420 with a Yamaha engine. If the part looks the same on your bike, it should fit.

Ich habe ein Winora Y 420 aus dem Jahr 2017 mit einem Yamaha Motor. Wenn das Teil an ihrem Fahrrad genauso aussieht dann sollte es passen.

Answer of Arie

Replacing the hardware is sufficient. Make sure you use exactly the correct year.

Vervangen van de hardware is voldoende. Zorg wel dat je exact de juiste jaargang gebruikt.

Answer of BERNARD

NO update needed

PAS de mise à jour nécessaire

Answer of Fabrice

Hello, replacing the hardware is enough. Sincerely

Bonjour, le remplacement du matériel suffit. Cordialement

Answer of Johan

All I remember is that for my wife’s bike, I had to make sure I purchase the right year model. Never did any software update and all works perfectly. I did for some reason move the position of the sensor on the spoke and didn’t realise it after assembly. So it didn’t line up and thus initially didn’t work leaving me a bit confused and thinking I would need to do software - but once I diagnosed that fault all has been good. I am not saying that you can’t do a software update, just that I have not had to do so. How that helps you get sorted… happy project

All I remember is that for my wife’s bike, I had to make sure I purchase the right year model. Never did any software update and all works perfectly. I did for some reason move the position of the sensor on the spoke and didn’t realise it after assembly. So it didn’t line up and thus initially didn’t work leaving me a bit confused and thinking I would need to do software - but once I diagnosed that fault all has been good. I am not saying that you can’t do a software update, just that I have not had to do so. How that helps you get sorted… happy project

Answer of Johan

No software update needed.

No software update needed.

Answer of Fabrizio

It is compatible with 2016 and 2017 products. Since 2018 the control lever has changed and is no longer compatible.

È compatibile con i prodotti del 2016 e 2017. Dal 2018 il manettino di comando è cambiato e la non è più compatibile.

Answer of Johan

There are two variants of Yamaha displays. The differences are best seen when the bike is turned off. On the 2014-2015 model, the time indication is just below the center of the display and on the 2016 model it is just above the center. This is the 2016 model.

There are two variants of Yamaha displays. The differences are best seen when the bike is turned off. On the 2014-2015 model, the time indication is just below the center of the display and on the 2016 model it is just above the center. This is the 2016 model.

Answer of Jesús Manuel

It is compatible with the 2016 model of ebike, not a motorcycle and not for later models.

Es compatible con el modelo del 2016 de ebike, no de una moto y no para modelos posteriores.

Answer of Jesús Manuel

Correct, this is the reference only the second 9 is not there.

Correcto, esta es la referencia solo que el segundo 9 no está.